“Aptio Setup Utility” is the BIOS (Basic Input/Output System) which is usually on the main board of a computer or laptop. This BIOS is a type of firmware that acts as an interface between the computer’s hardware and operating system. Problems may arise in Aptio setup utility – copyright (c) 2022/2023/2012, so let us see the solution to all these today.
If “Aptio Setup Utility” is appearing on your system, it means that your system has reached the BIOS settings screen. Usually this happens when the computer is unable to boot Windows and goes into BIOS. If you are facing any problem like “Copyright (c)” or other problems are arising, here are some common solutions which are as follows:
Aptio Setup Utility Problems and Their Solutions:
If your Aptiyo Setup Utility problem is shown for the first time, then first of all save & exit it. Or you can long press the power button and shut down the PC and start it again. This will solve the problem.
1. System is not booting (Boot Issue)
If the computer is not booting and goes directly to Aptio Setup Utility, then the reasons may be the following:
• Boot Device Selection:
- Go to BIOS and check the Boot Order. Make sure that your hard drive or SSD is number one as the boot device.
- Set the Boot Priority so that your OS (such as Windows) can boot correctly.
• UEFI/Legacy Mode:
- If your computer is set to UEFI mode and Windows is having trouble booting, go to the BIOS settings and try changing the boot mode from UEFI to Legacy or CSM (Compatibility Support Module) mode.
2. System Date and Time Issue
If the date and time in the BIOS are incorrect, it may be due to a discharged CMOS battery. You may need to replace the CMOS battery.
- To replace the CMOS battery, open the computer’s casing and look for a small battery on the motherboard. Replacing it may solve the problem.
3. “Copyright (c)” or licensing issues
This message usually appears when the system has not booted correctly after changing the BIOS settings for some reason. This may be due to a corrupt BIOS or software issue.
- Update BIOS: Visit your motherboard manufacturer’s website and update it by downloading the latest BIOS version.
- Restore BIOS Defaults: Go to BIOS settings and select the “Restore Defaults” or “Load Optimized Defaults” option. This will restore the settings and may resolve the issue.
4. Hardware Issues
Sometimes hardware issues may cause you to enter Aptio Setup Utility. Such as:
- RAM, hard drive, or other components are connected incorrectly.
- The hard drive or SSD connection may be loose.
- To reset the system: Unplug all connected hardware (such as RAM, SSD/HDD, and power cables), then reconnect and restart the system.
5. System Repair
If there is no problem with the BIOS but Windows is not booting, you can also perform a Windows repair.
Windows Recovery:
- Boot from the Windows installation media (USB or DVD).
- Click the “Repair your computer” option.
- Select “Troubleshoot” > “Advanced options” > “Startup Repair”.
6. Password/Password Recovery Issue
If a password is set in the BIOS and you have forgotten it, there are a few steps you can take to recover the password:
- Removing the CMOS battery: Removing the CMOS battery for a few minutes and then reinserting it may reset the password.
- You can also change the motherboard jumper settings to reset the BIOS password (these settings can be found in the motherboard manual).
7. Hard Disk Checking:
If you have tried all the above options but the problem still persists:
Open your computer and remove the hardice and then reinsert it. This will ensure that your hardice was not working in the first place. If the problem is due to the wire, then the problem will be solved.
Conclusion:
“Aptio Setup Utility” is usually part of the BIOS screen, and there can be many reasons why it appears. You should try to troubleshoot the problem with the above solutions. If the problem persists, there may be a more serious problem related to the motherboard or hardware, which may require technical assistance. You can also watch video solutions on our YouTube channel.
